TIP140, tip141, tip142 npn silicon power darlingtons
1 december 1971 - revised september 2002 specifications are subject to change without notice. designed for complementary use with tip145, tip146 and tip147 125 w at 25c case temperature 10 a continuous collector current minimum h fe of 1000 at 4 v, 5 a sot-93 package (top view) pin 2 is in electrical contact with the mounting base. mdtraaa b c e 1 2 3 absolute maximum ratings at 25c case temperature (unless otherwise noted) notes: 1. this value applies for t p 0.3 ms, duty cycle 10%. 2. derate linearly to 150c case temperature at the rate of 1 w/c. 3. derate linearly to 150c free air temperature at the rate of 28 mw/c. 4. this rating is based on the capability of the transistor to operate safely in a circuit of: l = 20 mh, i b(on) = 5 ma, r be = 100 ? , v be(off) = 0, r s = 0.1 ? , v cc = 20 v. rating symbol value unit collector-base voltage (i e = 0) TIP140 tip141 tip142 v cbo 60 80 100 v collector-emitter voltage (i b = 0) TIP140 tip141 tip142 v ceo 60 80 100 v emitter-base voltage v ebo 5v continuous collector current i c 10 a peak collector current (see note 1) i cm 15 a continuous base current i b 0.5 a continuous device dissipation at (or below) 25c case temperature (see note 2) p tot 125 w continuous device dissipation at (or below) 25c free air temperature (see note 3) p tot 3.5 w unclamped inductive load energy (see note 4) ?li c 2 100 mj operating junction temperature range t j -65 to +150 c storage temperature range t stg -65 to +150 c lead temperature 3.2 mm from case for 10 seconds t l 260 c
TIP140, tip141, tip142 npn silicon power darlingtons 2
december 1971 - revised september 2002 specifications are subject to change without notice. notes: 5. these parameters must be measured using pulse techniques, t p = 300 s, duty cycle 2%. 6. these parameters must be measured using voltage-sensing contacts, separate from the current carrying conta cts. ? voltage and current values shown are nominal; exact values vary slightly with transistor parameters. electrical characteristics at 25c case temperature parameter test conditions min typ max unit v (br)ceo collector-emitter breakdown voltage i c = 30 ma (see note 5) i b = 0 TIP140 tip141 tip142 60 80 100 v i ceo collector-emitter cut-off current v ce = 30 v v ce = 40 v v ce = 50 v i b =0 i b =0 i b =0 TIP140 tip141 tip142 2 2 2 ma i cbo collector cut-off current v cb = 60 v v cb = 80 v v cb = 100 v i e =0 i e =0 i e =0 TIP140 tip141 tip142 1 1 1 ma i ebo emitter cut-off current v eb = 5 v i c =0 2 ma h fe forward current transfer ratio v ce = 4 v v ce = 4 v i c = 5a i c =10a (see notes 5 and 6) 1000 500 v ce(sat) collector-emitter saturation voltage i b = 10 ma i b = 40 ma i c = 5a i c =10a (see notes 5 and 6) 2 3 v v be base-emitter voltage v ce = 4 v i c = 10 a (see notes 5 and 6) 3 v v ec parallel diode forward voltage i e = 10 a i b = 0 (see notes 5 and 6) 3.5 v resistive-load-switching characteristics at 25c case temperature parameter test conditions ? min typ max unit t on tu r n - o n t i m e i c = 10 a v be(off) = -4.2 v i b(on) = 40 ma r l = 3 ? i b(off) = -40 ma t p = 20 s, dc 2% 0.9 s t off turn-off time 11 s
TIP140, tip141, tip142 npn silicon power darlingtons 3
december 1971 - revised september 2002 specifications are subject to change without notice. typical characteristics figure 1. figure 2. figure 3. typical dc current gain vs collector current i c - collector current - a 05 20 10 10 h fe - typical dc current gain 70000 100 1000 10000 tcs140aa v ce = 4 v t p = 300 s, duty cycle < 2% t c = -40c t c = 25c t c = 100c collector-emitter saturation voltage vs collector current i c - collector current - a 05 20 10 10 v ce(sat) - collector-emitter saturation voltage - v 0 05 10 15 20 tcs140ab t p = 300 s, duty cycle < 2% i b = i c / 100 t c = -40c t c = 25c t c = 100c base-emitter saturation voltage vs collector current i c - collector current - a 05 20 10 10 v be(sat) - base-emitter saturation voltage - v 0 05 10 15 20 25 30 tcs140ac t c = -40c t c = 25c t c = 100c i b = i c / 100 t p = 300 s, duty cycle < 2%
TIP140, tip141, tip142 npn silicon power darlingtons 4
december 1971 - revised september 2002 specifications are subject to change without notice. maximum safe operating regions figure 4. thermal information figure 5. maximum forward-bias safe operating area v ce - collector-emitter voltage - v 10 10 100 1000 i c - collector current - a 01 10 10 100 sas140aa TIP140 tip141 tip142 maximum power dissipation vs case temperature t c - case temperature - c 0 25 50 75 100 125 150 p tot - maximum power dissipation - w 0 20 40 60 80 100 120 140 tis140aa
|
